Different Kinds of Sandwich Panel based on Application
Wall mounted sandwich panel is used in shed, workshop, official and residential walls with 4 to 6 c thickness, this type of sandwich panel is also suitable for internal walls and partitions in different projects with 4 to 6 cm thickness containing two layers of Aluzinc sheets, two galvanized layers and or inside Aluzinc and outside galvanized layer and it is possible to enhance compression strength by making groove in them to an optimal level. Eagle Panel wall mounted sandwich panel design is in such a way that there is an indentation in width from one side and there is a protuberance on another side (masculinity and femininity) that when two panels are next to each other, they are overlapped and it connects structure to fastener in different conditions, shed, workshop, official and residential wall mounted sandwich panel are different kinds of wall mounted sandwich panel. Wall mounted sandwich panel are prepared through different methods of two pre-colored Aluzinc sheets, two pre-colored galvanized sheets and or one Aluzinc sheet from outside and one galvanized sheet from inside with polyurethane insulator with 3.-40 kg/m3 density and the created groove causes optimal compression strength. Models are: straight (DNS), grooved (DND) and hidden screw (PRO). Sandwich panel has lots of characteristics in heat transfer issues, these are:
Ineffective against electricity
Ineffective against reaction against chemicals
Resistive function against heat
Resistance against water permeation
Wall mounted sandwich panel suck wind only when they are exposed to wind pressure and load. However, forces which are applied have to be considered. Structure engineer is the responsible to define and specify wind loads and anchorage distance in every project. Structure engineer has to be familiar with shape factor and other parameters and use instructions and other confirmed information in exposure building for local and general wind pressures.
This type of sandwich panel is produced in 8 to 20 cm thickness which has the least heat transfer due to its overlap kind and it is the best choice in producing icehouse. This type of sandwich panel is produced from 8 to 20 cm thickness considering heat exchange and it has the least heat transfer enjoying masculinity and femininity edges in width section and panes overlapping and it is the best choice to produce icehouse. Icehouse wall mounted sandwich panel produced in this industrial complex is prepared with 8-20 cm thickness, grooved sheet model with two importing Aluzinc layers (aluminum and zinc) and two pre-colored galvanized sheets in 0.5 thickness, 116 cm fixed width (useful width) in 1 to 6 m length. There is the least heat transfer in our sandwich panel because it is overlapped (masculinity and femininity) and it is the best choice to construct various icehouses in all geographical points of Iraq.
Double girder crane is stronger! If you need to displace heavy loads up to 120 ton throughout a wide region, double girder gantry crane constructed in Steel Eagle Factory is your best choice. Double girder gantry cranes of Steel eagle Co guarantees heavy and permanent performance, flexibility and usability. In order to achieve high performance, low weight and advantages like increasing resistance and reducing costs, all sections used for main beams (cranes girders) and heads are optimized by computer. Steel eagle double girder half gantry cranes are constructed with 40 m opening and it is possible to construct them with unlimited capacity and opening in Steel Eagle Engineering Co and they are flexible in specific conditions and needs. For example, faster longitudinal velocity, repairing and maintaining platforms, trolley and hoist units with auxiliary corridors and hoists are all among the features that may be applicable.
Will a crane with 180° rotation fulfill your needs? Arm wall mounted cranes is your solution. We can install a similar crane on a column in your factory building. It is obvious that this column must have appropriate dimensions. If it is needed, Steel Eagle Engineering Team will specify forces which are applied on that column.
Wall mounted cranes are mainly used for downloading and uploading machines.
Is your factory devoid of an appropriate wall or column to assemble crane? Do you need 270° or 360° rotation range? Column-mounted cranes are the best solution. Steel Eagle Co can offer crane with related column. The crane can be installed on an anchorage inside a hole existing in foundation and or on a flange installed on concrete floor of your factory (concrete floor thickness must be at least 20 cm). All movements can be done manually or electrically, moreover if your column-mounted cranes are galvanized, they can be used in open space.
Although arm cranes are ideal solution for limited displacement, you may cover a very larger range with wall-mounted cranes. Travelling arm wall-mounted crane is a travelling wall-mounted crane which does not need angular movement (rotating around one’s axis), so working range increases to full length of your salon. Travelling arm wall-mounted crane is very user-friendly solution along one side of salon, while overhead cranes may be used in higher level without any disturbances. If you are going to use arm wall-mounted crane, consider it during designing your building. If you need, Steel Eagle Co will offer information related to applicable force eagerly.
Fast and easy carrying and installation to store food and sanitary stuffs/ easy and fast washability/ insulation against coldness and heat/ resistant against environmental conditions and corrosions. Our icehouse sandwich panel is very resistant against compressive and impact loads due to using so light polyurethane insulator, 40 times lighter than brick wall and due to polyurethane molecular structure. Eagle Panel sandwich panel is very resistant against environmental conditions like moisture, corrosion and… due to using pre-colored Aluzinc sheet with 25 µ furnace polyester color from outside and 7 µ from inside. Among the other advantages of this wall mounted sandwich panel is relatively high performance for installation so that a 4 people group are able to install 300 to 400 m2 per day.
This kind off sandwich panels are very resistant against corrosion and corruption and microbes and bacteria aggregation on it is at least due to its smooth surface and other properties and it is used in 4 to 6 cm thicknesses with two layers of Aluzinc sheets with 0.6 to 0.7 sheet thickness for hospital surgery room, drug production workshops, vaccination production workshops, foodstuffs workshops, laboratories and medical equipment production workshops.
It is used to insulate fixed icehouses floor and then it is covered by concrete after installation and minimizes heat transfer from the floor of icehouse. This type of sandwich panel is used to insulate fixed icehouses floor and two nylon sheets are used instead of two metal ones and it is lighter than other sandwich panels and it is covered by concrete after insulation and minimizes heat transfer from the floor of icehouse. This act has reduced heat transfer from the floor of icehouse in duplex nylon wall mounted sandwich panels and among its advantages are appropriate price and light weight. Duplex nylon sandwich panels are used as sound and heat proof in addition to icehouse floors in dropped ceiling and building walls.
Overhead sandwich panel prevents water permeation considering its trapezoidal steps and overlap shape and it is able to be overlapped on each other in long lengths (loner than 13 m). This type of sandwich panel is produced as two layers of Aluzinc sheets and one Aluzinc sheet from outside and one aluminum reinforced foil from inside with 4 to 10 cm thickness. Overhead sandwich panel is produced in trapezoid shadow-line design and this design is recognized in the external sheet appearance of sandwich panel and the factory produces sheet with pottery design for beautiful ceiling view in sloping mode, it is possible to make a ceiling with very beautiful view by constructing truss. This panel is resistant against plants and fungi growth and it is the best kind of coverage in industrial complexes ceiling because of materials not falling and impossibility for insects to live inside foam. Overhead panel is among the best industrial insulator with very low thermal conductivity to cover ceiling. Overhead panel useful width is 1.01 m that it is 1.08 m considering overlap. Also the shape of overlap is in such a way that creates the best type of sealing and beauty on work surface during overlapping two overhead panels on each other. Another kind of panels produced by Eagle Panel Co is sheet from one side and aluminum foil or paper from another side which is the best option for dropping ceiling and coverage over industrial buildings and shed storages.